- #Willem eprom programmer pcb 5.0 download manual install
- #Willem eprom programmer pcb 5.0 download manual software
- #Willem eprom programmer pcb 5.0 download manual code
- #Willem eprom programmer pcb 5.0 download manual trial
- #Willem eprom programmer pcb 5.0 download manual windows
There is also some of low level code, and using for it interpreter is mediocre idea in my opinion, but. Python - no I have no experience with it, and the syntax is not convenient for me (waf was implemented by yannick ). Not that Geepro should use Python, I was.
It is interpreted, true, but a lot of system calls available in C are available in Python. Python is actually a wrapper to make C easier. On 02:20 PM, Krzysztof Komarnicki wrote: Thanks, done. But as I mentioned above, I have no experience with Python.
#Willem eprom programmer pcb 5.0 download manual code
This approach would eliminate necessity of recompilation code to add new IC. Not that Geepro should use Python, I was curious what your thoughts are." So, maybe only plugins for ICs should be in Python and the rest in C/C++. "Python is actually a wrapper to make C easier.
#Willem eprom programmer pcb 5.0 download manual trial
I'm using trial and error and its time consuming as having to wipe the failed chip each time. What settings work best for burning 27512 chips. I can read chips OK but having difficulty writing them.
#Willem eprom programmer pcb 5.0 download manual software
I got the software up and running on ubuntu 18.04 with a chinese writer. A help file would be really 'helpful' ) It all depends on the voltage required to burn the 27XX chip, which varies by chip size and manufacturer. On 11:06 AM, Spooky Dillow wrote: I got the software up and running on ubuntu 18.04 with a chinese writer. It would have made the project worthwhile had I got a result. Its a shame as its been great fun learning about the lpt port under ubuntu. usb and 13.8v (which works with windows) too. I've tried it as sudo and myself with varying voltages, i.e. I've also managed to write to a chip on two occassions but the write was unsuccessful. I can get the softwear to read chips and veryfy they are blank. I've tried just about everything I can with this and have to admit defeat. Do you have jumpers set to old version (version 3 not 5.0e - jumpers near DB25 connector ) ? Currently I cannot check it because I have no willem board. It's hard to find schematic for this version (found very poor scan), but I see it is something changed in shift registers for address. Sincerely many thanks for trying to help me.
#Willem eprom programmer pcb 5.0 download manual windows
I will have to resort to windows software to do the work. Im not sure the board is willem, its probably a copy. Thanks for the advice but it still doesn't write to the chips correctly. src/error.h ( macros _ERROR, ERROR and MESSAGE )Ĭould you add to program crc16add algoritm and computed result like windows version? Thanks. If you have a problem with compilation add spaces around "format" -> " format " in. So thanks beforehand.Ĭurrent version from repository has already this feature.
That is why this project got stalled if you ask me. First and foremost developers should take this into consideration and I feel the developers here a left a huge chunk of information out thinking it is obvious for everyone to know, which obviously isn't the case as I have pointed out.
#Willem eprom programmer pcb 5.0 download manual install
Judder, it would be interesting if you showed us the complete procedure you followed to install this software on your Ubuntu because most Willem Programmer users are electronics geegs, not linux geeks. Developers should take this fact into consideration and I feel the developers here left a huge chunk of information out thinking it is obvious for everyone to know, which obviously isn't the case as I have pointed out.
Judder, it would be interesting if you showed us the complete procedure you followed to install this software on your Ubuntu because most Willem Programmer users are electronics geeks, not linux geeks. On 04:40 PM, Phoebus1966 wrote: Judder, it would be interesting if you showed us the complete procedure you followed to install this software on your Ubuntu because most Willem Programmer users are electronics geegs, not linux geeks.
0 kommentar(er)
